How to Fix Garage Door Problems


Whether your garage door has a bent or broken torsion spring, cable, or roller, there are several steps you can take to repair it. First, place a block of wood on the side of the door where it is bent or dented. This will prevent the door from further bending.

Repairing a broken torsion spring

Identifying the problem is the first step in the process. Before proceeding, ensure you have the correct type of garage door opener and know what to look for. It is essential to measure the spring coils to ensure you are not breaking the spring itself. You should place a hook between two coils and measure the overall length. Then, divide the measurements by 20 or 40 to determine the overall wire diameter.

A broken torsion spring can be challenging to replace. You’ll need a unique tool to perform the replacement. It can cost anywhere from $15 to $100, depending on the type and size of the spring. You will also need a sturdy ladder and safety goggles. Although the process is simple, it is essential to take safety precautions while attempting the repair.

Repairing a bent garage door

When repairing a bent garage door, it is best to call a professional garage door repair service instead of trying to fix it yourself. It is tial to follow the correct procedure and don’tnotexcessive force to straighten the dent. Incorrect force can cause more damage to the dent and make the dent bigger. You should also avoid hammering the bent area as it will likely bend again at the same spot. Another alternative to hammering is the use of suction cups. This method is best for minor dents and can be used to straighten the dent in metal doors.

When it comes to straightening a bent garage door panel, one of the first things you need to do is lift the damaged panel off its track. Next, check the hinge pins that hold the door panels together. If you notice rust on these pins, you can clean them with water and soap. It would help if you also lubricated them with a lubricant. Finally, allow the door to dry completely before reassembling it.

Repairing a broken cable

If you are having trouble opening and closing your garage door, it may be time to consider repairing the cable. Often, broken cables result from excessive wear and tear, and they may also be rusting or oxidized. Replacing the cable protects the door from breaking and helps keep it in good shape. It does not have to be difficult, and customer support can guide you through the process.

First, make sure to lock your garage door in place. Then, if necessary, you can use vice grips to secure the door. You may also need a ladder to keep the door from moving. Once you reach the cable, you can remove it from the drum at the bottom of the door. Next, you should loop the new cable around the peg on the bottom of the door.

Repairing a broken roller

A broken roller in a garage door can be challenging to diagnose. Sometimes, it might be caused by force from a car’s impact or a lack of lubrication. In such cases, replacing the rollers may be necessary. To replace a broken roller, unplug the garage door opener and disengage the emergency release. Afterward, test the door to determine which roller is broken.

To replace a broken roller, start by pulling the bottom section toward the inside of the garage. Then, bend the track so that you can remove the roller. This will make it easier to replace the roller. When you replace the roller, ensure the guide holes in the brackets are perpendicular to the track. If the roller is twisted, you may need to bend the bracket at the lower point to straighten it.

Replacing a circuit board

Replacing a circuit board for shaky, noisy, or unresponsive garage doors can be easy and cost-effective. Circuit boards send and receive information from a remote control, so the door operates as instructed. A damaged circuit board may result in the door not operating correctly or even tripping during a storm. If you suspect your circuit board has failed, you should check your power supply first.

After locating the circuit board, call a garage door technician. Professional technicians are trained to inspect these circuits and circuit boards properly. They know the dangers of tampering with the wiring and can determine whether a new board is necessary. After determining the cause of the malfunction, the technician will unplug the old circuit board and replace it with the new one.

Repairing a broken track

There are several steps to follow when fixing a broken garage door track. First, determine the location of the broken track. This will make adjusting the new track easier. Next, unscrew the screws that hold the broken track to the wall. Work from the bottom to avoid falling track pieces. Then, measure and mark the new track’s location.

If you cannot do this yourself, you should consider hiring a professional garage door repair company. These professionals will diagnose the problem and apply a fast repair. However, it is essential to be cautious when trying to repair a garage door track because if it is not done correctly, it may result in injury or even death.